• Specifications

    Stand-alone system for acquiring data facility-wide.

    Learn More
    Slide 1
  • Accessories

    Housed in a NEMA-12 rated enclosure for harsh environments.

    Learn More
    Slide 2
  • Downloads

    View and download the user manual.

    Learn More
    Slide 3

EDAS-1027


EDAS-1000E Series Ethernet Data Acquisition Systems are stand-alone data acquisition systems that connect to and communicate over Ethernet (IEEE 802.310Base-T) Local Area Networks(LANs). They use the open systems environment of Ethernet and Transmission Control Protocol/Internet Protocol (TCP/IP, a standard networking protocol that provides communication across interconnected networks). These features enable you to integrate acquired data with your facility-wide or world-wide network, making the data available for use by other networked resources, or for further processing by personal or company software.

The EDAS-1027 Industrial EDAS systems are housed in NEMA-12 rated enclosures for use in harsh environments. It provides 16 digital I/O channels, which are individually configurable as inputs or outputs. With the use of isolated signal conditioning modules, 10 to 280 Volt I/O ranges are supported. Any signal conditioning or isolation modules used are within the enclosure.

Specifications

Digital I/O

  • 8 channels (bits) per port (4 programmable for input or output)
  • TTL-compatible (Schmitt Trigger) input levels
  • Input current:
    • Port 0 (high level/low level): 20μA/200μA
    • Port 1 (high level/low level): 5μA/5μA
  • TTL-compatible output levels
  • Output current:
    • Port 0 (source/sink): 15mA/24mA
    • Port 1 (source/sink): 15mA/64mA

Counters

  • General purpose: 24-bit
    • Up to 32 channels
    • Max input frequency (TTL-level input): 250Hz
  • 16-bit high speed
    • Used with the EDAS-2002M-1 module
    • Max input frequency (TTL-level input): 250kHz

Serial Ports

  • RS-232
    • DE-9 connector
    • Serial asynchronous (ASCII) communication
    • Supply voltages (3k ohm load):
      • ±6V TX
      • 16-bit
      • RX active
  • RS-485 (EDAS-1001E-2C)
    • 3-wire screw terminal block connector
    • Serial asynchronous (ASCII) communication
    • Isolation (1 minute): 1600 Vrms

Network Interface

  • Ethernet 10Base-T (RJ45)
  • 8kHz system throughput (unloaded network)

Power

  • Voltage range (AC or DC): 15 to 28 VAC, 20 to 40 VDC
  • Current requirements* (24VAC, no load/1A load): 200mA/500mA

Physical

  • 6.00″ D x 5.57″ W x 1.52″ H (15.24 cm D x 14.15 cm W x 3.86 cm H)
  • 0° to 50° C**
  • *The on-board power supply circuit can supply up to 1A @ 5VDC to termination panels through the 50-pin I/O connectors
  • **All specifications are typical at 25° C unless otherwise noted

Accessories

EDAS-1018A-1

EDAS-1018A-1

Operator interface cable, for use with TM2500 microterminals. RS-232, DE-9 male to DE-9 female, 3 meters

EDAS-1024A-1

EDAS-1024A-1

Industrial EDAS enclosure

LPP002

LPP002

24VAC power supply (90-120VAC input)

LPP003

LPP003

24VAC power supply (90-120VAC input)

LPA015

LPA015

Data Transfer Cable, RS-232, DE-9 (AT) and DB-25 (XT)

EDAS-1028A-1

EDAS-1005A-1

DIN-rail mounting kit for EDAS-1001E and EDAS-1002E Ethernet data acquisition systems. Includes aluminum strap and mounting screws.

EDAS-1028A-1

EDAS-1028A-1

Rack-mount kit, 19-inch, for EDAS-1001E, EDAS-1002E and EDAS-1031E systems. Includes 1U-size rack-mount and overlays for installation of up to 3 EDAS units.

Downloads

EDAS 1000 Series Manual

User Manual for the EDAS-1000 Data Acquisition Systems series.